CLM Enterprises. the home for your breathing needs.    HACKER SAFE certified sites prevent over 99.9% of hacker crime.  

 Axis HVLP Automotive painting system Quantity   

This system, the Axis SP2003, is quality-built with a high output three stage turbine which provides the power you need to atomize high viscosity materials. It comes standard with a professional series HVLP spray gun designed to give automotive finish quality results. Designed for all stages of finish work on autos, airplanes and marine, fine woodworking, and modeling. This system is versatile and powerful enough to use for practically any painting task. Polyurethane, Epoxy, Waterborne, Multi-Color, Fillers, and Gel Coats.

--WHEN YOU NEED ONLY A PAINT TRANSPORT SYSTEM
its = "referrer=

FREE GROUND SHIPPING THIS MONTH (USA)

 Axis 3 STAGE HVLP pump

bullet High Output 3 Stage Turbine 5.5 PSI, 110 cfm
bullet20' of 3/4' Tiger flex Spray Hose
bullet4' Whip Hose  
bulletPro Series BOTTOM FEED Spray Gun ( TOP FEED $60.00 MORE CALL)
bullet1.1 mm Needle Nozzle
bulletQuick Disconnect
bulletAir Control Valve
bullet"How to Spray" Instruction Guide
bullet Instruction Manual
bulletincoming Air filter system
bullet ACCUSPRAY gun (LEX_AIR gun $50.00 More call)

SUGGESTED RETAIL $799.00          

CLM� PRICE� $699.00               

Quantity
with top feed gun$859.00
CLM PRICE $759.00
 
Quantity
AXIS 4 STAGE HVLP PUMP
  This system, the Axis SP2004, is quality-built with a high output four stage turbine which provides the power you need to atomize high viscosity materials, 7.5 PSI at the gun. It comes standard with a professional series HVLP spray gun designed to give automotive finish quality results. It will provide you with the extra atomization necessary for the finest finish. Designed for all stages of finish work on autos, airplanes an
with top feed gun$859.00
CLM PRICE $759.00
 
Quantity
AXIS 4 STAGE HVLP PUMP
  This system, the Axis SP2004, is quality-built with a high output four stage turbine which provides the power you need to atomize high viscosity materials, 7.5 PSI at the gun. It comes standard with a professional series HVLP spray gun designed to give automotive finish quality results. It will provide you with the extra atomization necessary for the finest finish. Designed for all stages of finish work on autos, airplanes and marine, fine woodworking, and modeling. This system is versatile and powerful enough to use for practically any painting task. Polyurethane, Epoxy, Waterborne, Multi-Color, Fillers, and Gel Coats, Clear Coats. The 4 stage has all the features as the 3 stage above only with a more powerful motor.

 

     

SUGGESTED RETAIL $899.00  with top feed gun $959.00
CLM  PRICE  $799.00
Quantity
CLM price top feed gun$859.00

Quantity

MARKSMAN PAINTING SYSTEM

Description:
 
The MARKSMAN HVLP Paint Sprayer is a combination of the very best HVLP components available put together into one "very easy to use" and portable system! You can find lesser expensive systems, but they lack the quality of the MARKSMAN. The MARKSMAN is great for the woodworker, cabinetmaker or modeler. Great portability along with the same professional quality HVLP Spray Gun offered with our                            other HVLP Spray Systems.

Features:
bulletTwo Stage, Single Speed Turbine 
bullet20' of 3/4 Tiger flex Air Hose
bulletPRO  Bottom Feed Spray Gun with 1 qt. Cup (TOP FEED $60.00 MORE)
bullet1.0 mm L/A Needle Nozzle
bulletQuick Disconnect
bulletAir Control Valve
bulletInstruction Manual
bulletOutput: 50 cfm - 3.5 psi
bulletAccuspray gun ( LEX-AIR gun $50.00 more call)
 

Retail price $599.00  

CLM Price $550.00  

Quantity
 
 
*Painting Accessory Products

No compressor is needed to operate the system, which eliminates the oil and moisture problem so prevalent with other kinds of sprayers. Another advantage is that the system is totally portable, lightweight and uses standard household electricity. A natural by-product of any turbine system is the addition of heat to the airline. The advantage of the heat is that it eliminates moisture from the air that is mixed with the paint, however, the disadvantage of this heat is that it has a tendency to also flash away some of the thinner that is added to the paint when it is mixed. This loss of thinner can render the paint droplets too dry when they are applied causing an 'orange peel' effect. The solution is to add more thinner to the paint when it is mixed to compensate for its loss. The turbine raises the temp of the air 20 degrees above the air, which must be taken into consideration in high room temperature (the motor should be run for a few minutes to let the air temperature adjust to a steady degree). Another way to help to control the heat is to add a short piece of natural rubber 'stub hose' at the pump outlet. We call it an 'HD' or heat dissipation hose and is included in every AXIS spray system.

The way to get a great finish when spraying is to have a system that will break up the paint droplets as small as possible when it is atomized, the smaller the droplets, the better the finish.  Because this atomization (mixing the paint with the air) takes place as the paint exits the nozzle and mixes with the air it stands to reason that the smaller the nozzle hole is, the smaller the droplets are broken down.

  The big advantage to HVLP is that it saves you at least 50% of your paint with 90% of the paint going to the surface and STAYING thus eliminating the over spray and allowing you to actually see what you are painting.  With other options the web site http://clmcenterprises.com has a lot more information or if you have questions not covered please call me toll free at 877-949-5183 or Email sales@clmcenterprises.com

                                                                                                                                                        Our units are Proudly Manufactured in the USA in Gilberts Il.

  ALL ITEMS ARE IN STOCK. ALL ORDERS PLACED BY 1PM CST WILL BE SHIPPED SAME DAY

*US funds $ dollars Prices subject to change without notice.� no guarantee on pricing in case of misprints

BACK TO TOP          Back to Main menu

Contact Information

Telephone
877-949-5183         Toll Free
 
Postal address
555 Rock Creek Dr.
             Manyeno,IL.60950
Electronic mail
General Information: Info@clmcenterprises.com
Sales: Sales@clmcenterprises.com
Customer Support: support@clmcenterprises.com
Webmaster: TeamZen Web Services
CLM. Enterprises is an authorized distributor for Axis Corp and the 3M Corp.    
Fast Counter by Link Exchange ielogo[1].gif (7090 bytes)