|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
| ||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|---|
4 stage system
Your selection of the four stage CITATION over the three stage CITATION should be considered when the finest finish possible is desired. Cool Fresh Air to breathe, The extra power of 7.5 psi (4 stage) instead of 5.5 psi (3 stage) will greatly reduce the particle size in the material being sprayed. The smaller the particle size equates to the finest finish.
In addition, because the four stage pump offers this abundance of power, the painter's attention to paint mixture, reduction of material and spray gun technique is not nearly as critical as with a three stage system. This makes the four stage system a logical choice for the novice as well as the pro who demands high quality.
Pricing
4 stage system
| citation | Suggested Retail* | CLM Price |
|---|---|---|
| Citation 440 (40ft hose, half mask) |
$1545.00 |
Quantity |
| with air supplied hood don't forget the lens protectors> | $1555.00 | |
| Citation 440F (40ft hose, full mask ) | $1655.00 | Quantity |
| Citation440 Buddy (2 PEOPLE SYSTEM 2 hoses two 1/2 masks) | $1741.00 | Quantity |
| Citation 440 Buddy system F1/2 ( Full face Mask & 1/2 mask) | $1851.00 | |
| Citation 440 Buddy two 40 ft hoses, (2 air supplied hoods ) | $1761.00 | Quantity |
| Citation 440 Buddy 2 40 ft hoses (!/2 mask & air supplied hood)don't forget the lens protectors> | $1751.00 | |
| Citation 440 Buddy two 40 ft hoses, two full face masks don't forget the lens protectors> | $1961.00 | |
| Citation 440 Buddy two 40 ft hoses, full face mask & air supplied hood | $1861.00 | |
| Add top feed to gun | $75.00 | |
| Substitute 3m Accuspray gun for LEX-AIR gun |
$100.00
| |
| Lens protectors for full mask Lens protectors for hood 25 for $25.00 |
Axis Products,
Inc. is the only company on planet Earth who offers a sprayer system like
this! Its design fresh-air breathing device that would be always
available for you to be able to breathe safely and comfortably while
spraying toxic materials. Deadly isocyanates, VOC s and other toxins present
in today's paint demand you use a Fresh Air Respirator. No other system
offers "built in" respirator protection with state of the art HVLP paint
sprayer in the same cabinet. Components designed to last a lifetime of
rigorous use. Easy to use. Just plug in, turn on the switch and go. This
unit includes a mask, two 40' hoses, the ”LEX-AIR” spray gun with a one
quart cup and whip hose and hose belt attachment (tie the two hoses
together). If you place ½ mask under a sand blast hood, welding helmet or
paint hood you will stay cool and not fog up lenses.
No compressor is needed to operate the system, which eliminates the oil and moisture problem so prevalent with other kinds of sprayers. Another advantage is that the system is totally portable, lightweight and uses standard household electricity. A natural by-product of any turbine system is the addition of heat to the airline. The advantage of the heat is that it eliminates moisture from the air that is mixed with the paint, however, the disadvantage of this heat is that it has a tendency to also flash away some of the thinner that is added to the paint when it is mixed. This loss of thinner can render the paint droplets too dry when they are applied causing an 'orange peel' effect. The solution is to add more thinner to the paint when it is mixed to compensate for its loss. The turbine raises the temp of the air 20 degrees above the air, which must be taken into consideration in high room temperature (the motor should be run for a few minutes to let the air temperature adjust to a steady degree). Another way to help to control the heat is to add a short piece of natural rubber 'stub hose' at the pump outlet. We call it an 'HD' or heat dissipation hose and is included in every AXIS spray system.
The way to get a great finish when spraying is to have a system that will break up the paint droplets as small as possible when it is atomized, the smaller the droplets, the better the finish. Because this atomization (mixing the paint with the air) takes place after the nozzle of the spray gun just as it exits, it stands to reason that the smaller the nozzle hole is, the smaller the droplets are broken down. The big advantage to HVLP is that it saves you at least 50% of your paint with 90% of the paint going to the surface and STAYING thus eliminating the over spray and allowing you to actually see what you are painting.
We also have many Painting accessories and additional Products to help you get the job done right the first time With other options the web site http://clmcenterprises.com has a lot more information or if you have questions not covered please call me toll free at 877-949-5183 or Email clmcarcare1@gmail.comOur units are Proudly Manufactured in the in Gilberts Il.
For more info on the CITATION
Click here for INFO good paint job
US funds $ dollars Prices subject to change without notice. no guarantee on pricing in case of misprints.
| CLM. Enterprises is an authorized distributor for Axis Corp and the 3M Corp. | |